23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated
23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated
23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated
23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated
23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated
23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated
23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated
23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated
23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated
23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated
23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated
23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated
23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated
23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated

23/64" End Mill Single End Square. Flute Length 7/8" - OAL 2-1/2" - 3 Flute. TiN Coated

End Mill
$17.30 each
Item #
Series
Coating
Quantity
- +

23/64" cutting diameter, 3 flutes, single end, square end, TiN coated.

Ground from solid carbide. This tool cuts 23/64" diameter, has 7/8" of flute and measures 2-1/2" overall.

The square end cuts a flat floor with a sharp corner — slots, pockets, shoulders and side milling.

The TiN coating adds surface hardness and lubricity over uncoated carbide or HSS in general-purpose work.

Specifications

  • Cutting diameter: 23/64"
  • Length of cut (LOC): 7/8"
  • Overall length (OAL): 2-1/2"
  • Flutes: 3
  • End type: Single End
  • End geometry: Square End
  • Coating: TiN
  • Tool material: Solid Carbide
  • Series: 125
  • Item number: 125-3359

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide