1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated

1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes Uncoated

End Mill
$15.06 each
Item #
Series
Coating
Quantity
- +

1/64" cutting diameter, 2 flutes, single end, ball nose, uncoated.

Ground from solid carbide. This tool cuts 1/64" diameter, has 1/16" of flute and measures 1-1/2" overall.

The ball nose leaves a radiused bottom, which is what you want for 3D contours, fillets and mould surfaces rather than flat floors.

Uncoated, so the edge stays as sharp as it can be ground — the usual choice for aluminium and other soft, sticky materials.

Specifications

  • Cutting diameter: 1/64"
  • Length of cut (LOC): 1/16"
  • Overall length (OAL): 1-1/2"
  • Flutes: 2
  • End type: Single End
  • End geometry: Ball Nose
  • Coating: Uncoated
  • Tool material: Solid Carbide
  • Series: 135
  • Item number: 135-2015

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide