1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated
1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated

1/64" End Mill Single End Ball. Flute Length 1/16" - OAL 1-1/2" 2 Flutes TiN Coated

End Mill
$16.33 each
Item #
Series
Coating
Quantity
- +

1/64" cutting diameter, 2 flutes, single end, ball nose, TiN coated.

Ground from solid carbide. This tool cuts 1/64" diameter, has 1/16" of flute and measures 1-1/2" overall.

The ball nose leaves a radiused bottom, which is what you want for 3D contours, fillets and mould surfaces rather than flat floors.

The TiN coating adds surface hardness and lubricity over uncoated carbide or HSS in general-purpose work.

Specifications

  • Cutting diameter: 1/64"
  • Length of cut (LOC): 1/16"
  • Overall length (OAL): 1-1/2"
  • Flutes: 2
  • End type: Single End
  • End geometry: Ball Nose
  • Coating: TiN
  • Tool material: Solid Carbide
  • Series: 140
  • Item number: 140-2015

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide