1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated
1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated
1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated
1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated
1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated
1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated
1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated
1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated
1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated
1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated
1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated
1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated
1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated
1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated

1/32" End Mill Single End Ball. Flute Length 3/32" - OAL 1-1/2" 2 Flutes AlTiN Coated

End Mill
$10.43 each
Item #
Series
Coating
Quantity
- +

1/32" cutting diameter, 2 flutes, single end, ball nose, AlTiN coated.

Ground from solid carbide. This tool cuts 1/32" diameter, has 3/32" of flute and measures 1-1/2" overall.

The ball nose leaves a radiused bottom, which is what you want for 3D contours, fillets and mould surfaces rather than flat floors.

AlTiN is built for heat: stainless, tool steels and high-temperature alloys, especially with little or no coolant.

Specifications

  • Cutting diameter: 1/32"
  • Length of cut (LOC): 3/32"
  • Overall length (OAL): 1-1/2"
  • Flutes: 2
  • End type: Single End
  • End geometry: Ball Nose
  • Coating: AlTiN
  • Tool material: Solid Carbide
  • Series: 145
  • Item number: 145-2031

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide