5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated
5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated
5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated
5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated
5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated
5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated
5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated
5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated
5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated
5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated
5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated
5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated
5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated
5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated

5/32" End Mill Single End Ball. Flute Length 9/16" - OAL 2" - 4 Flutes AlTiN Coated

End Mill
$12.78 each
Item #
Series
Coating
Quantity
- +

5/32" cutting diameter, 4 flutes, single end, ball nose, AlTiN coated.

Ground from solid carbide. This tool cuts 5/32" diameter, has 9/16" of flute and measures 2" overall.

The ball nose leaves a radiused bottom, which is what you want for 3D contours, fillets and mould surfaces rather than flat floors.

AlTiN is built for heat: stainless, tool steels and high-temperature alloys, especially with little or no coolant.

Specifications

  • Cutting diameter: 5/32"
  • Length of cut (LOC): 9/16"
  • Overall length (OAL): 2"
  • Flutes: 4
  • End type: Single End
  • End geometry: Ball Nose
  • Coating: AlTiN
  • Tool material: Solid Carbide
  • Series: 145
  • Item number: 145-4156

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide