1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated
1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated
1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated
1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated
1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated
1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated
1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated
1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated
1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated
1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated
1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated
1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated
1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated
1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated

1/4" End Mill Single End Square. Long Length. Flute Length 1-1/8" OAL 3" - 4 Flutes Uncoated

End Mill
$14.04 each
Item #
Series
Coating
Quantity
- +

1/4" cutting diameter, 4 flutes, single end, square end, long length, uncoated.

Ground from solid carbide. This tool cuts 1/4" diameter, has 1-1/8" of flute and measures 3" overall.

The square end cuts a flat floor with a sharp corner — slots, pockets, shoulders and side milling.

The long flute gives more usable depth than a standard length.

Uncoated, so the edge stays as sharp as it can be ground — the usual choice for aluminium and other soft, sticky materials.

Specifications

  • Cutting diameter: 1/4"
  • Length of cut (LOC): 1-1/8"
  • Overall length (OAL): 3"
  • Flutes: 4
  • End type: Single End
  • End geometry: Square End
  • Length style: Long
  • Coating: Uncoated
  • Tool material: Solid Carbide
  • Series: 150
  • Item number: 150-4250

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide