7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated
7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated
7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated
7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated
7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated
7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated
7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated
7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated
7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated
7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated
7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated
7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated
7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated
7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated

7/16" End Mill Single End Square. Long Length. Flute Length 2" OAL 4" - 2 Flutes AlTiN Coated

End Mill
$47.66 each
Item #
Series
Coating
Quantity
- +

7/16" cutting diameter, 2 flutes, single end, square end, long length, AlTiN coated.

Ground from solid carbide. This tool cuts 7/16" diameter, has 2" of flute and measures 4" overall.

The square end cuts a flat floor with a sharp corner — slots, pockets, shoulders and side milling.

The long flute gives more usable depth than a standard length.

AlTiN is built for heat: stainless, tool steels and high-temperature alloys, especially with little or no coolant.

Specifications

  • Cutting diameter: 7/16"
  • Length of cut (LOC): 2"
  • Overall length (OAL): 4"
  • Flutes: 2
  • End type: Single End
  • End geometry: Square End
  • Length style: Long
  • Coating: AlTiN
  • Tool material: Solid Carbide
  • Series: 160
  • Item number: 160-2437

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide