1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated
1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated
1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated
1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated
1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated
1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated
1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated
1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated
1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated
1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated
1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated
1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated
1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated
1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated

1/4" End Mill Single End Ball Nose. Long Length. Flute Length 1-1/8" OAL 3" - 2 Flutes AlTiN Coated

End Mill
$24.55 each
Item #
Series
Coating
Quantity
- +

1/4" cutting diameter, 2 flutes, single end, ball nose, long length, AlTiN coated.

Ground from solid carbide. This tool cuts 1/4" diameter, has 1-1/8" of flute and measures 3" overall.

The ball nose leaves a radiused bottom, which is what you want for 3D contours, fillets and mould surfaces rather than flat floors.

The long flute gives more usable depth than a standard length.

AlTiN is built for heat: stainless, tool steels and high-temperature alloys, especially with little or no coolant.

Specifications

  • Cutting diameter: 1/4"
  • Length of cut (LOC): 1-1/8"
  • Overall length (OAL): 3"
  • Flutes: 2
  • End type: Single End
  • End geometry: Ball Nose
  • Length style: Long
  • Coating: AlTiN
  • Tool material: Solid Carbide
  • Series: 165
  • Item number: 165-2250

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide