1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated
1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated
1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated
1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated
1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated
1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated
1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated
1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated
1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated
1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated
1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated
1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated
1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated
1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated

1/2" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiN Coated

End Mill
$97.01 each
Item #
Series
Coating
Quantity
- +

1/2" cutting diameter, 4 flutes, single end, square end, extra long length, TiN coated.

Ground from solid carbide. This tool cuts 1/2" diameter, has 3" of flute and measures 6" overall.

The square end cuts a flat floor with a sharp corner — slots, pockets, shoulders and side milling.

The extra length reaches into deep pockets and past fixturing that a standard tool cannot clear.

The TiN coating adds surface hardness and lubricity over uncoated carbide or HSS in general-purpose work.

Specifications

  • Cutting diameter: 1/2"
  • Length of cut (LOC): 3"
  • Overall length (OAL): 6"
  • Flutes: 4
  • End type: Single End
  • End geometry: Square End
  • Length style: Extra Long
  • Coating: TiN
  • Tool material: Solid Carbide
  • Series: 172
  • Item number: 172-4500

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide