1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated
1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated
1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated
1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated
1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated
1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated
1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated
1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated
1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated
1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated
1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated
1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated
1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated
1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated

1" End Mill Single End Square. Extra Long Length. Flute Length 3" OAL 6" - 4 Flutes TiCN Coated

End Mill
$423.89 each
Item #
Series
Coating
Quantity
- +

1" cutting diameter, 4 flutes, single end, square end, extra long length, TiCN coated.

Ground from solid carbide. This tool cuts 1" diameter, has 3" of flute and measures 6" overall.

The square end cuts a flat floor with a sharp corner — slots, pockets, shoulders and side milling.

The extra length reaches into deep pockets and past fixturing that a standard tool cannot clear.

TiCN is harder than TiN and holds up better in abrasive materials and higher feeds.

Specifications

  • Cutting diameter: 1"
  • Length of cut (LOC): 3"
  • Overall length (OAL): 6"
  • Flutes: 4
  • End type: Single End
  • End geometry: Square End
  • Length style: Extra Long
  • Coating: TiCN
  • Tool material: Solid Carbide
  • Series: 174
  • Item number: 174-4100

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide