1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated
1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated
1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated
1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated
1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated
1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated
1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated
1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated
1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated
1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated
1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated
1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated
1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated
1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated

1/2" End Mill Single End Ball. Extra Long Length. Flute Length 1-1/2" OAL 6" - 2 Flutes Uncoated

End Mill
$95.49 each
Item #
Series
Coating
Quantity
- +

1/2" cutting diameter, 2 flutes, single end, ball nose, extra long length, uncoated.

Ground from solid carbide. This tool cuts 1/2" diameter, has 1-1/2" of flute and measures 6" overall.

The ball nose leaves a radiused bottom, which is what you want for 3D contours, fillets and mould surfaces rather than flat floors.

The extra length reaches into deep pockets and past fixturing that a standard tool cannot clear.

Uncoated, so the edge stays as sharp as it can be ground — the usual choice for aluminium and other soft, sticky materials.

Specifications

  • Cutting diameter: 1/2"
  • Length of cut (LOC): 1-1/2"
  • Overall length (OAL): 6"
  • Flutes: 2
  • End type: Single End
  • End geometry: Ball Nose
  • Length style: Extra Long
  • Coating: Uncoated
  • Tool material: Solid Carbide
  • Series: 175
  • Item number: 175-2506

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide