3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated
3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated
3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated
3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated
3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated
3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated
3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated
3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated
3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated
3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated
3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated
3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated
3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated
3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated

3/4" End Mill Single End Ball. Long Reach. Shank OD 3/4 LOC 1" OAL 4" - 2 Flutes Uncoated

End Mill
$171.48 each
Item #
Series
Coating

3/4" cutting diameter, 2 flutes, single end, ball nose, long reach length, uncoated.

Ground from solid carbide. This tool cuts 3/4" diameter, has 1" of flute and measures 4" overall.

The ball nose leaves a radiused bottom, which is what you want for 3D contours, fillets and mould surfaces rather than flat floors.

The necked long-reach body gets the cutting edge down into a deep feature while keeping the shank close to full diameter for rigidity.

Uncoated, so the edge stays as sharp as it can be ground — the usual choice for aluminium and other soft, sticky materials.

Specifications

  • Cutting diameter: 3/4"
  • Length of cut (LOC): 1"
  • Overall length (OAL): 4"
  • Flutes: 2
  • End type: Single End
  • End geometry: Ball Nose
  • Length style: Long Reach
  • Coating: Uncoated
  • Tool material: Solid Carbide
  • Series: 743
  • Item number: 743-5932

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide