7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated
7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated
7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated
7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated
7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated
7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated
7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated
7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated
7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated
7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated
7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated
7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated
7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated
7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated

7/8" End Mill Single End Square. Shank OD 7/8" Flute Length 1-1/2" OAL 4" - 6 Flutes - AlTiN Coated

End Mill
$256.88 each
Item #
Series
Coating
Quantity
- +

7/8" cutting diameter, 6 flutes, single end, square end, AlTiN coated.

Ground from solid carbide. This tool cuts 7/8" diameter, runs a 7/8" shank, has 1-1/2" of flute and measures 4" overall.

The square end cuts a flat floor with a sharp corner — slots, pockets, shoulders and side milling.

AlTiN is built for heat: stainless, tool steels and high-temperature alloys, especially with little or no coolant.

Specifications

  • Cutting diameter: 7/8"
  • Shank diameter: 7/8"
  • Length of cut (LOC): 1-1/2"
  • Overall length (OAL): 4"
  • Flutes: 6
  • End type: Single End
  • End geometry: Square End
  • Coating: AlTiN
  • Tool material: Solid Carbide
  • Series: 792
  • Item number: 792-6875

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide