1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated
1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated
1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated
1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated
1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated
1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated
1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated
1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated
1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated
1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated
1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated
1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated
1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated
1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated

1" End Mill Single End Square. Long Reach. Shank OD 1" LOC 1-1/4" OAL 7" - 2 Flutes Uncoated

End Mill
$523.13 each
Item #
Series
Coating
Quantity
- +

1" cutting diameter, 2 flutes, single end, square end, long reach length, uncoated.

Ground from solid carbide. This tool cuts 1" diameter, runs a 1" shank, has 1-1/4" of flute and measures 7" overall.

The square end cuts a flat floor with a sharp corner — slots, pockets, shoulders and side milling.

The necked long-reach body gets the cutting edge down into a deep feature while keeping the shank close to full diameter for rigidity.

Uncoated, so the edge stays as sharp as it can be ground — the usual choice for aluminium and other soft, sticky materials.

Specifications

  • Cutting diameter: 1"
  • Shank diameter: 1"
  • Length of cut (LOC): 1-1/4"
  • Overall length (OAL): 7"
  • Flutes: 2
  • End type: Single End
  • End geometry: Square End
  • Length style: Long Reach
  • Coating: Uncoated
  • Tool material: Solid Carbide
  • Series: 740
  • Item number: 740-4934

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide