41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated
41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated
41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated
41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated
41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated
41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated
41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated
41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated
41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated
41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated
41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated
41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated
41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated
41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated

41/64" End Mill Single End Ball. Flute Length 1-1/2" - OAL 4" - 4 Flutes AlTiN Coated

End Mill
$193.35 each
Item #
Series
Coating
Quantity
- +

41/64" cutting diameter, 4 flutes, single end, ball nose, AlTiN coated.

Ground from solid carbide. This tool cuts 41/64" diameter, has 1-1/2" of flute and measures 4" overall.

The ball nose leaves a radiused bottom, which is what you want for 3D contours, fillets and mould surfaces rather than flat floors.

AlTiN is built for heat: stainless, tool steels and high-temperature alloys, especially with little or no coolant.

Specifications

  • Cutting diameter: 41/64"
  • Length of cut (LOC): 1-1/2"
  • Overall length (OAL): 4"
  • Flutes: 4
  • End type: Single End
  • End geometry: Ball Nose
  • Coating: AlTiN
  • Tool material: Solid Carbide
  • Series: 145
  • Item number: 145-4640

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide