1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated
1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated
1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated
1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated
1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated
1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated
1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated
1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated
1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated
1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated
1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated
1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated
1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated
1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated

1/2" End Mill Single End Square. Long Reach. Shank OD 1/2" LOC 5/8" OAL 4" - 2 Flutes AlTiN Coated

End Mill
$68.93 each
Item #
Series
Coating

1/2" cutting diameter, 2 flutes, single end, square end, long reach length, AlTiN coated.

Ground from solid carbide. This tool cuts 1/2" diameter, runs a 1/2" shank, has 5/8" of flute and measures 4" overall.

The square end cuts a flat floor with a sharp corner — slots, pockets, shoulders and side milling.

The necked long-reach body gets the cutting edge down into a deep feature while keeping the shank close to full diameter for rigidity.

AlTiN is built for heat: stainless, tool steels and high-temperature alloys, especially with little or no coolant.

Specifications

  • Cutting diameter: 1/2"
  • Shank diameter: 1/2"
  • Length of cut (LOC): 5/8"
  • Overall length (OAL): 4"
  • Flutes: 2
  • End type: Single End
  • End geometry: Square End
  • Length style: Long Reach
  • Coating: AlTiN
  • Tool material: Solid Carbide
  • Series: 741
  • Item number: 741-9695

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide