1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated — HTC Mfg.
1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated
1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated
1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated
1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated
1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated
1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated
1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated — HTC Mfg.
1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated
1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated
1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated
1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated
1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated
1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated

1/4" End Mill Single End Square. Tapered Mill. Shank OD 3/8" - LOC 2" OAL 4" - 3 Flutes TiCN Coated

End Mill
$109.11 each
Item #
Series
Coating
Quantity
- +

1/4" cutting diameter, 3 flutes, single end, square end, TiCN coated.

Ground from solid carbide. This tool cuts 1/4" diameter, runs a 3/8" shank, has 2" of flute and measures 4" overall.

The square end cuts a flat floor with a sharp corner — slots, pockets, shoulders and side milling.

TiCN is harder than TiN and holds up better in abrasive materials and higher feeds.

Specifications

  • Cutting diameter: 1/4"
  • Shank diameter: 3/8"
  • Length of cut (LOC): 2"
  • Overall length (OAL): 4"
  • Flutes: 3
  • End type: Single End
  • End geometry: Square End
  • Coating: TiCN
  • Tool material: Solid Carbide
  • Item number: 98269

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide