5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated
5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated
5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated
5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated
5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated
5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated
5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated
5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated
5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated
5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated
5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated
5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated
5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated
5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated

5/16" End Mill Single End Square. Shank OD 5/16" Flute Length 7/8" OAL 2-1/2" - 6 Flutes - Uncoated

End Mill
$11.81 each
Item #
Series
Coating
Quantity
- +

5/16" cutting diameter, 6 flutes, single end, square end, uncoated.

Ground from solid carbide. This tool cuts 5/16" diameter, runs a 5/16" shank, has 7/8" of flute and measures 2-1/2" overall.

The square end cuts a flat floor with a sharp corner — slots, pockets, shoulders and side milling.

Uncoated, so the edge stays as sharp as it can be ground — the usual choice for aluminium and other soft, sticky materials.

Specifications

  • Cutting diameter: 5/16"
  • Shank diameter: 5/16"
  • Length of cut (LOC): 7/8"
  • Overall length (OAL): 2-1/2"
  • Flutes: 6
  • End type: Single End
  • End geometry: Square End
  • Coating: Uncoated
  • Tool material: Solid Carbide
  • Series: 790
  • Item number: 790-6312

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide