7/32" End Mill Single End Square. Corner Radius .060" - Shank OD 1/4'' Flute Length 5/8" OAL 2-1/2" - 2 Flutes - AlTiN Coated — HTC Mfg.
7/32" End Mill Single End Square. Corner Radius .060" - Shank OD 1/4'' Flute Length 5/8" OAL 2-1/2" - 2 Flutes - AlTiN Coated
7/32" End Mill Single End Square. Corner Radius .060" - Shank OD 1/4'' Flute Length 5/8" OAL 2-1/2" - 2 Flutes - AlTiN Coated
7/32" End Mill Single End Square. Corner Radius .060" - Shank OD 1/4'' Flute Length 5/8" OAL 2-1/2" - 2 Flutes - AlTiN Coated — HTC Mfg.
7/32" End Mill Single End Square. Corner Radius .060" - Shank OD 1/4'' Flute Length 5/8" OAL 2-1/2" - 2 Flutes - AlTiN Coated
7/32" End Mill Single End Square. Corner Radius .060" - Shank OD 1/4'' Flute Length 5/8" OAL 2-1/2" - 2 Flutes - AlTiN Coated

7/32" End Mill Single End Square. Corner Radius .060" - Shank OD 1/4'' Flute Length 5/8" OAL 2-1/2" - 2 Flutes - AlTiN Coated

Solid Carbide Corner Radius End Mill
$15.48 each
Item #
Series
Coating

7/32" cutting diameter, 2 flutes, single end, corner radius, AlTiN coated.

Ground from solid carbide. This tool cuts 7/32" diameter, runs a 1/4" shank, has 5/8" of flute and measures 2-1/2" overall.

The corner radius takes the load off the weakest point of the tool, so the edge lasts longer than a sharp corner in the same cut.

AlTiN is built for heat: stainless, tool steels and high-temperature alloys, especially with little or no coolant.

Specifications

  • Cutting diameter: 7/32"
  • Shank diameter: 1/4"
  • Length of cut (LOC): 5/8"
  • Overall length (OAL): 2-1/2"
  • Flutes: 2
  • End type: Single End
  • End geometry: Corner Radius
  • Coating: AlTiN
  • Tool material: Solid Carbide
  • Series: 360
  • Item number: 360-2218-060

Availability and Shipping

For HTC carbide tools, coating service typically adds 2–3 calendar days when the uncoated tool is available. If the tool is not in stock, estimated time to ship is 7–10 calendar days.

Estimated time to ship is measured in calendar days, from order placement until your order is handed to the carrier. Carrier transit time is additional. Orders may ship sooner. We accept orders awaiting replenishment; please contact us before ordering if you need a specific shipping date.

See our Shipping Policy for details.

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide