1/4" Beefy End Mill Ball End Straight Flute LOC 3/4" OAL 2-1/2" - 2 Flutes Uncoated
1/4" Beefy End Mill Ball End Straight Flute LOC 3/4" OAL 2-1/2" - 2 Flutes Uncoated
1/4" Beefy End Mill Ball End Straight Flute LOC 3/4" OAL 2-1/2" - 2 Flutes Uncoated
1/4" Beefy End Mill Ball End Straight Flute LOC 3/4" OAL 2-1/2" - 2 Flutes Uncoated
1/4" Beefy End Mill Ball End Straight Flute LOC 3/4" OAL 2-1/2" - 2 Flutes Uncoated
1/4" Beefy End Mill Ball End Straight Flute LOC 3/4" OAL 2-1/2" - 2 Flutes Uncoated
1/4" Beefy End Mill Ball End Straight Flute LOC 3/4" OAL 2-1/2" - 2 Flutes Uncoated
1/4" Beefy End Mill Ball End Straight Flute LOC 3/4" OAL 2-1/2" - 2 Flutes Uncoated
1/4" Beefy End Mill Ball End Straight Flute LOC 3/4" OAL 2-1/2" - 2 Flutes Uncoated
1/4" Beefy End Mill Ball End Straight Flute LOC 3/4" OAL 2-1/2" - 2 Flutes Uncoated
1/4" Beefy End Mill Ball End Straight Flute LOC 3/4" OAL 2-1/2" - 2 Flutes Uncoated
1/4" Beefy End Mill Ball End Straight Flute LOC 3/4" OAL 2-1/2" - 2 Flutes Uncoated

1/4" Beefy End Mill Ball End Straight Flute LOC 3/4" OAL 2-1/2" - 2 Flutes Uncoated

End Mill
$23.48 each
Item #
Series
Coating
Quantity
- +

1/4" cutting diameter, 2 flutes, ball nose, uncoated.

Ground from solid carbide. This tool cuts 1/4" diameter, has 3/4" of flute and measures 2-1/2" overall.

The ball nose leaves a radiused bottom, which is what you want for 3D contours, fillets and mould surfaces rather than flat floors.

The straight flute takes no helix angle, so it pulls neither up nor down on the work — useful on thin material and in slotting.

Uncoated, so the edge stays as sharp as it can be ground — the usual choice for aluminium and other soft, sticky materials.

Specifications

  • Cutting diameter: 1/4"
  • Length of cut (LOC): 3/4"
  • Overall length (OAL): 2-1/2"
  • Flutes: 2
  • End geometry: Ball Nose
  • Flute form: Straight flute
  • Coating: Uncoated
  • Tool material: Solid Carbide
  • Item number: 91612

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide