9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated
9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated
9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated
9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated
9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated
9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated
9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated
9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated
9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated
9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated
9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated
9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated
9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated
9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated

9/16" End Mill Single End Square. Shank OD 9/16" Flute Length 1-1/4" OAL 3-1/2" - 6 Flutes - Uncoated

End Mill
$50.82 each
Item #
Series
Coating
Quantity
- +

9/16" cutting diameter, 6 flutes, single end, square end, uncoated.

Ground from solid carbide. This tool cuts 9/16" diameter, runs a 9/16" shank, has 1-1/4" of flute and measures 3-1/2" overall.

The square end cuts a flat floor with a sharp corner — slots, pockets, shoulders and side milling.

Uncoated, so the edge stays as sharp as it can be ground — the usual choice for aluminium and other soft, sticky materials.

Specifications

  • Cutting diameter: 9/16"
  • Shank diameter: 9/16"
  • Length of cut (LOC): 1-1/4"
  • Overall length (OAL): 3-1/2"
  • Flutes: 6
  • End type: Single End
  • End geometry: Square End
  • Coating: Uncoated
  • Tool material: Solid Carbide
  • Series: 790
  • Item number: 790-6562

Recently viewed

Dial In Your Cut

Free TechTips resources for end mill users — machinist tested.

Speeds & Feeds CalculatorsThe right RPM and feed rate for your end mill, material and setup.Open calculator → Chip Load (FPT) CalculatorFeed per tooth keeps carbide cutting instead of rubbing — with chip thinning compensation.Open calculator → MRR CalculatorHow hard your end mill is really working, and where your cycle time goes.Open calculator →

More help: Milling TechTips · Troubleshooting · Carbide vs. HSS Guide